Beginner's Plumbing: The Essentials for Bathtub Installation
Beginner's Plumbing: The Essentials for Bathtub Installation
Blog Article
What are your opinions concerning How to Install a Bathtub Yourself?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably challenging project. If the old tub is readily easily accessible, the job can move speedily; if you need to open up a wall surface to eliminate the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will need an assistant to vacate the old tub and also set in the brand-new one. Make sure you have actually certified yourself for the task and also are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about using one prior to you start. Chances are you might require a specialist plumber to make tube links.
This short article will assist you set up a new bath tub in your shower room if you have actually already bought a new tub as well as don't require to change the arrangement of your previous water supply pipelines.
Your devices and also product list must comprise the following:
Planning for the Installation
Firstly, the sustaining structure supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its final setting.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is separate the water supply. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be rather bothersome due to the limited access that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will come from the pipelines. When the supply pipelines have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the tub in the needed position. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bathtub till the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest flexible faucet adapter to the ideal supply pipe by making a compression join; then do the exact same for the other faucet.
Activate the supply of water and also inspect all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the bathtub and additionally check the overflow outlet and also the typical electrical outlet for leaks.
Finally, fix the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the tub needs to wait up until the bathtub has been used at the very least when as this will settle it into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet and also the sink. Secure the tap in place with the supplier given backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former kind should be attached to the faucet finishes first, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, triggering the water to penetrate the wall surface between the bath and the tiling, causing complications with moisture and feasible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and also cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly fill the tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can crack rather very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily offered on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that post about Tools You Need to Install a New Bathtub when doing a lookup on the web. Do you know about somebody who is interested by the subject? Take a moment to share it. I enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.
Professional help? One call away. Report this page